FIE, LLC - Services & Prices
MAGNETOS
$269
Standard Mag Service
Includes load testing one external transformer/points box at no extra cost
Super-Mags/Sprintmags:
Pre-test, tear down, clean, magnet charge, new points, all new hardware, new bearings, new harness, exchange plates, factory label, run-in, check/adjust individual cylinder timing, adjust edge-gap, post-test, output report. Add $0 for rotation change
MSD Mags:
Tear down, clean, new bearings, pickup adjust, new hardware, check/adjust individual cylinder timing, adjust polewheel clearance, rotor phasing, output test, report. Add $125 for rotation change
Vertex/Scintilla:
Pre-test, tear down, clean, magnet charge, new bearing, new hardware, lubricate, adjust clearance, run-in, check/adjust break-angle, post-test, output report. Add $95 for rotation change
Rotation change without service:
$99
Super-Mag/Sprintmag
$195
MSD Mag
$159
Vertex
$25
Load test coil or points box
Beyond ONE included in STD service
$199
Convert Sprintmag to Sprintmag II
Add to STD service: New upper housing for screw-down cap, 205M screw-down cap included
$179
New Super-Mag/Sprintmag Housing
Add new gold irridite housings to STD service, old housing exchanged
$639
Upgrade any Super-Mag to 5A SMIV
STD service, PLUS: new NEO (rare-earth) magnet/poleshoe/shaft assy, 1.0uF capacitor
$489
Upgrade Sprintmag I/II to 3A Sprintmag+
STD service, PLUS: new NEO (rare-earth) magnet/polewheel/shaft assy, SPM+ winding assy, capacitor
$449
Upgrade Vertex OAC to 2-2.5A
STD service, PLUS: new NEO (rare-earth) magnet/polewheel/shaft assy, capacitor
$579
Upgrade Vertex OAC to 3-3.5A
STD service, PLUS: new NEO (rare-earth) magnet/polewheel/shaft assy, HIGH-OUTPUT internal coil, capacitor
$969
Upgrade/conversion from Vertex OAC to OXC
STD service, PLUS, cap/rotor and conversion kit, new internal winding, new NEO (rare earth) magnet/polewheel/shaft assy, capacitor and bracket, oil filled external coil, harnesses.
$1029
Upgrade Mag 12 to 20
STD service, PLUS: two new 44 magnet assemblies, upper and lower shaft/reluctor (rotation change at no extra charge)
$130
Convert 8106 Box to EXTERNAL COIL capability
Install FIE terminal block in place of stock coil, 4' (trim to length) Weather-Pak harness, load test. Includes Terminal block, harness and labor only - external coil not included.
$359
Upgrade Mag 12 small cap to 4" Medium cap
Cap, ring, blue rotor, hold-down, upper shaft, magneto upper body ring
$339
MSD cap/rotor conversion for Super-Mag/Sprintmag
Utilize all MSD cap/rotor hardware; includes cap, rotor, ring, hold-down, body adapter and rotor adapter
$1,589
Upgrade any Super-Mag to 10A Super-Mag+ (Severe-duty Points)
STD service, new NEO magnet/poleshoe/shaft assy, Severe-Duty points, SM+ winding assy, capacitors, Monster 5" MSD cap kit, factory label, polish
$1,179
Upgrade any Super-Mag to 8A Super-Mag V (Severe-duty Points)
STD service, new NEO magnet/poleshoe/shaft assy, Severe-Duty points, SM V winding assy, capacitors, spacer and rotor adapter for taller points, factory label, polish
$TBD
Repair 28901 or 28944 Monster Red transformer
Laminations, windings, terminals, gasket, oil, decals. Load test
MECHANICAL FUEL SYSTEMS
$95
Tear down, inspect, clean, lid seal, bolts, flow test fuel pump. Traditional style Enderle & Hilborn and including Waterman Sprint.
$130
Tear down, inspect, clean, all o-rings, flow test large spur gear fuel pumps up to 30 GPM. Waterman Bertha, Rage, Aeromotive, etc.
$139
Tear down, inspect, clean, RECLEARANCE, flow test traditional Enderle/Hilborn style fuel pump
$219
Freshen Enderle pump (parts & labor): New bearings, new shaft seal, reclearance, flow test.
$100
Setup Sheet: Check valve pressures, initial start-up settings, nozzle sizing and placement, main pill and high-speed pressure calculations. Questionnaire required.
$239
Precision Calculated Tuneup: Check valve pressures, start-up settings, nozzle sizing and placement, main/sizer/low-speed/high-speed pill and pressure calculations, customized weather tuning info and math, schematic. Questionnaire required.
$769
System flow/Refurb (SC or NA): Clean and reseal all components, reclearance pump, pump profile test, match set of nozzles to within 1%, flow system for best pill at selected weather. High-speed setup, weather tuning info, etc. Questionnaire required.
$119
Add 8 port nozzles to system flow work
$56
Price for parts added to convert legacy Hilborn pump shaft seal assembly to standard spring lip seal.
$249
Convert flange style Enderle/Hilborn pump to slip-collar, includes collar, reclearance, machining labor, flow test
$12
Flow test nozzle jet or bypass pill, match within 1% at specified pressure, w/report
ELECTRONIC FUEL SYSTEMS
$12.50
Flow test electronic fuel injector (static & pulse) with report
$25
Recondition electronic injector: before/after flow tests, ultra-sonic cleaning, new filters, pintle caps, spacers, o-rings. With report
$90
Recondition a pair of THROTTLE BODY (side feed) injectors: Before/after flow tests, ultra-sonic cleaning, new filters, seals, o-rings, with report. Ask about quantity discounts for more than two.
Questionnaires:
In order to flow your fuel system or calculate tuneup info and achieve the most accurate results possible, we'll need a bunch of information from you. Please print and fill out the appropriate questionnaire below as best you can and send it to us with your hardware. You could also "cut and paste" this info into an email and send it to: web@fuelinjectionent.com. Or, you could FAX it to: 541-205-4706.
Don't worry if there are items on the questionnaire that you don't know. Do the best you can and if we need to, we'll call you to discuss your setup.